Tuesday, September 17, 2013

Adventures in Liquid Soapmaking - Hints and Tips I've Learned Along the Way

So........ I have been working/experimenting with Liquid Soap Making for the past 2 1/2 years and while I love the process and everything that I have learned along the way, it is far trickier to accomplish successfully and consistently than cold process soap making.  Fortunately, the ingredient cost is minimal so I have not lost too much in materials (only time) during these past 2 + years of learning, experimenting, getting frustrated and achieving success.  (Updated 5/2014, 7/2014)





Here I share some of the hints and tips I have learned along the way.


1.  Start with a pre-made paste (I used Brambleberry's 100% Castile Paste) to understand the dilution process.  Since this is a 100% Olive Oil paste, it will take a lot of distilled water to dilute allowing you to see what a skin is and how to effectively continue to slowly add more water until full dilution.  Because it is 100% Olive Oil, you can also experiment with using non iodized table salt (dissolved in distilled water) to thicken your soap.  Dilution should be done very slowly by adding small amounts of boiled distilled water at a time, allowing the paste to dissolve into the water, then add more water if necessary.  Patience is key to avoid over dilution and too thin a soap.  Every formulation you create will have different dilution amounts.  The method you use to create the soap will also affect the amount of dilution water needed to fully dilute your paste to the desired consistency.

2.  Use a reliable calculator that takes into account the 90% purity if KOH.  These include Summerbee Meadow (also allows dual lye calculations), Brambleberry and Soapcalc.  Summerbee Meadow and Brambleberry are calibrated to a slight lye excess and you will probably get the same calculations from them.  Soapcalc has two options, one for straight KOH and one for 90% pure KOH - each will give results slightly different than the first two.

3.  Clear soap tested after a 3 hour cook (or any amount of time) does NOT mean you do not have excess KOH in your paste.  See #3. Excess KOH is the result of using a lye excess in your formulation.

4.  Phenolphthalein Drops are a my most important tool for testing for excess lye and if the soap is done.   Some people use the Zap test (place a bit of paste on their tongue to see if it zaps like a 9V battery placed on the tongue).  Soap paste is done (no excess lye) when the paste stays clear or very, very pale pink after adding a drop.  You can also titrate a diluted sample which is a bit more accurate. This does not mean your pH is low.  True liquid soap will have a pH in the range of 9.2 - 10.5. The more you superfat you soap, the lower you pH may be, but you will have problems with too much of a superfat in liquid soap. You can have a clear test of drops and a high pH soap so always test your pH with a reliable pH meter too on a very diluted room temperature sample. Testing for a lye excess is far more important than just testing your pH.

5.  Use Digital pH Meters on cooled, highly diluted soap (1% solution of paste in distilled water) when you need an accurate ph reading NOT pH papers or test strips.  pH is affected by temperature and concentration and readings while soap is hot or highly concentrated will be lower than readings at room temperature. It is not the pH that is lower, but just the accuracy of the readings. It is very hard to troubleshoot liquid soap problems without an accurate pH reading and papers/test strips cannot do that as they only give a range.  There can be a very big difference in how your soap looks and behaves at a pH of 9.5, 8.7 and  8.2 and troubleshooting this can be hampered when you do not have an accurate reading. Please see the post on pH readings, lowering pH

6.  Thickeners.  I use only non-iodized table salt,  HEC (Hydroxyethyl Cellulose) or HPMC (Hydroxypropyl methylcellulose) to thicken my liquid soaps and shampoos when needed.  All work well (salt for 100% olive oils or those very low in coconut oil) and HEC and HPMC for the rest.  HPMC works very well at very low rates (.5% - .7% depending on how thick your soap is to begin with) on mixed lye soaps (those created from both sodium hydroxide and potassium hydroxide).  HEC is wonderful when you want to insure that your soap will maintain its clarity.  HPMC at amounts greater than 1% have caused a bit of cloudiness in my previously clear soap - but again, you need less of the HPMC in dual lye soaps and in that case, it is not an issue as clarity remains at the lower levels of usage.  Note: there are other thickeners out there, but these are the ones that I have experience with and use.

7.  Neutralization - neutralization when referring to liquid soap is not getting your soap to a neutral pH (7.0).  It is the process of removing any excess lye that exists in your paste.  Older formulations and methods of creating liquid soaps used a lye excess to account for impurities in KOH to insure all oils were saponified and a clear soap was achieved.  That excess lye was then neutralized with the addition of borax, boric acid or citric acid after dilution.  The calculators we now have access to take into account the impurities in KOH to give us much more accurate lye amounts needed to saponify our oils so an excess is no longer necessary.  Using these updated calculators, you can even superfat your formula at 1 to 3% and still have a clear soap without the need to neutralize.   Keep in mind too that clarity is also affected by the oils you choose.  Some oil/butters have unsaponifiables or are high in palmatic and stearic acids that will create a cloudy soap and should not be used or used in small amounts if you want a clear soap.  Oils and ingredients with animal fats (tallow, lard, goat's milk) often create a soap that has a pearlescent effect to them.

8.  If adding Citric Acid, it should be added when the water/citric acid solution is super hot AND the diluted soap is hot.  You may see tiny white curdles or streaks when first added, but if you do not use too much, those will incorporate back into the diluted soap.  Be very, very careful lowering the pH with citric acid as too much and it will cloud your soap and take it out of solution (separation will occur).  I also find that after liquid soap sequesters a bit, the pH naturally lowers on its own.

9.  Plain fresh seltzer water (not a bottle that has been opened and sat around for a day or so - it will have lost too much of the carbonation) will neutralize excess KOH during the dilution phase.   I am  still experimenting with this but my tests show that 1 ounces seltzer water per 12 ounces paste reduces the PH by .1 - .15.  Would love to hear what others have experienced with using seltzer water as I am still experimenting with this.

10.  If your soap separates out after diluting because your ph got too low by adding too much citric acid  or other neutralizers/ph adjusters (nothing is more frustrating than to pour a batch of just diluted, beautifully clear soap into your storage container only to see it separate out - a layer of thickness on the top - the next morning) - heat the soap back up, dissolve a bit of KOH into distilled water and add it back to your soap.  Let cool and sit again.  If it still separates, you can repeat the process.  Add just a little bit at a time as you do not want to end up with a now caustic soap with excess lye.

11.  I still cannot get a completely clear goat's milk soap.  They develops a sludge that settles to the bottom and a pearlescent effect in the soap.  Coconut Milk is far less problematic.  The sludge can be strained out using a mesh strainer and several layers of paper towels.  Goat's Milk liquid soap will be much darker than soaps not make with goat's milk.  Many have tried to cold process the goat's milk soap paste to prevent it from heating up too much to try to reduce the dark appearance (this is not an issue with coconut milk).  If cold processing goat's milk soap paste, be aware that when you dilute the paste, if you use too much heat, you will be further cooking your paste and it will darken up anyways.  ETA (6/2014) - I have finally come up with a way to get as clear a goat's milk soap as possible and have a tutorial of this method posted.

12.  You can use a variety of liquids to dissolve your KOH.  Distilled water, heated glycerin, milks or any combination.  Using glycerin for all or part of your liquids speeds up the process to get you to your cook time (trace) much faster.  My 50/50 formulations (50% distilled water and 50% glycerin) get to the cook stage within 10 minutes .  When using milk for part of the liquid, I like to add them cold at trace.

13.  You can use a variety of methods to make your paste.  The three I use to dissolve your lye are 100% distilled water, a mix of distilled water and glycerin, and 100% glycerin.  You can use other liquids to dissolve your lye, but take good notes to see how they affect your finished soap.  If you use the mixed water/glycerin methods you can add your glycerin to your melted oils as long as you have enough water to fully dissolved your lye(s).  I shoot for a 1:1.1 ratio of lye:water with the remaining liquid amount in glycerin added to the oils.  I have tutorials for all three methods.

14.  Fragrance and Essential Oils.  Another thorn in my side.......... Again, nothing is worse than having a beautifully clear diluted liquid soap cloud up or separate out because of the fragrance oil or essential oil added.  Always test a small amount of diluted soap (4 or 5 ounces) with the fragrance or essential oil.  Some will cloud your soap, some will thin it out, some will thicken it.  Fragrance and Essential Oils are not water soluble so I add them to warm to hot soap.  Some people use polysorbate 80 to make them water soluble.  So far the following have worked well for me without a solubizer:

 - Lavender EO
 - Peppermint EO
 - Rosemary EO
 - Fresh Mango (Brambleberry)
 - Tropical Vacation (Brambleberry - clouds up at first and takes several days to clear)
 - Lime EO
 - White Tea and Ginger (Brambleberry)
 - Awapuhi (Elements Bath and Body)
 - Coconut Cybilla (Brambleberry)
 - Apricot Freesia (Wholesale Supplies Plus) - this is my absolute favorite.
 - Dancing Waters and April Showers (Wholesale Supplies Plus)
 - Lime Ginger (Elements Bath and Body)
 - Bamboo Sugarcane (Elements Bath and Body)

I do wish suppliers would have more information about how their fragrances perform in liquid soap like some do for cold process soap.  Knowing how a fragrance performs for the product you are making saves so much time and energy.  ETA - Brambleberry is now indicating how some fragrances perform in liquid soap!!!

15.  It is easy to add water soluble additives to your soap/shampoos.  I add panthenol and proteins and even water soluble shea butter to my soaps after/during dilution.  Just be careful with adding any botanicals and proteins and research which preservatives you might want to consider when adding botanicals.  You can also add these ingredients in their powdered form during dilution (dissolve into the dilution water) - but they should be dissolved in water prior to adding to your soap.  Liquid forms are typically heat sensitive so consider adding those when the soap is cool.



13. The more coconut/babassu oil in a formulation, the more the initial mixture will puff up during the emulsification process before you cook the paste - so plan accordingly to make sure your pot/crock pot is large enough.  This is probably due to the nature of coconut/babassu oil in creating a more bubbly finished product - but not sure.  Those high in these hard oils will have a tendency to "Volcano" or puff up enough that it will overflow your pot - keep an eye on it and never leave these pastes to cook without supervision.

14.  Preservatives - there is a lot of discussion regarding the need to preserve liquid soap.  Many people will not use preservatives and many will always use preservatives.  Liquid soap naturally has a pH of 9 - 10.  Oftentimes the pH will be lower than that due to intentional lowering of the pH or by the additives used during/after dilution.  Most bacteria will not grow in a high pH product (over 10) but the lower the pH, the higher chance that the environment will be conducive to bacterial growth.  Mold and yeast will grow at higher pH levels than bacteria.  Also, many additives create an environment more conducive to bacterial growth (proteins and water soluble extracts).  I have been advised that it is a good idea to preserve your soap if the pH is lower than 10.  The problem then becomes which preservative to use for liquid soap.  Many preservatives have pH restrictions that do not go high enough for our alkaline soap products.  There are two that I will use - Suttocide A which is a broad spectrum preservative effective up to a pH of 12 and Liquid Germall, also broad spectrum, which indicates a max pH of 8, but experts in the field of cosmetics have indicated that it is effective up to a pH of 10.  Both are used at low percentages and both are heat sensitive and should be added to cool soap.  Suttocide A will react to citral which is an ingredient in citrus Essential Oils and Fragrance Oils and it will turn your soap from pink to deep red.  Also, good manufacturing principles and using clean, disinfected equipment will play a role.  More information on preservatives can be found here. This is an excellent resource for preservatives in general.

15.  Soap concentration and dilution - How concentrated you want your finished soap to be will affect your dilution ratios.  Many people dilute there soap only with enough water to try to create a thicker finished soap.  These soaps are typically very, very concentrated and a little will go a long way and it is very possible that you may be wasting your soap with such high concentrations of paste.  I prefer to dilute the soap to the concentrations that works for the intended purpose of the soap (body wash, facial wash, cleaning soap) and then thicken it up to the preferred viscosity for the purpose of the soap.  When I make body washes, the dilution ratios are such that a small amount of soap on the scrubby (about quarter size dollop) is plenty to fully wash the entire body - but, this leaves the soap on the thin side.  If I had increased the concentration to start with a thicker soap, I would be wasting way too much of it as just a small dollop would be more than needed for a shower.  Thus, I will dilute these to the proper concentration of finished soap, then thicken them up with appropriate thickeners, some of which add extra benefits to your soap.

That's all for now.  I will update this post as I continue with my Adventures in Liquid Soapmaking.......

~ Faith

Copyright 2006 - 2015 Alaiyna B. Designs.  All rights reserved.  All text and images are the property of Alaiyna B. Designs.  No part of this document or webpage may be reproduced by any means without prior written consent of Alaiyna B. Designs.

24 comments:

  1. Thanks so much for this information! I found it to be a shinig light in a dark forest! Diane

    ReplyDelete
  2. Can I please ask you a question? I really need advice and I've search high and low and can't find anything that can help me. I've been making cold process soap now for about 2 years and I love making it. So finally I decided to try my hand at making liquid soap. I worked all night one night putting together recipes and had one ready for the first thing in the morning. When I woke up I jumped right into it. Then after cooking three hours I tested the paste and it was clear. It was when I did the dilution phase that I realized that something was wrong with my soap. The problem is no matter how much water I add it thickens back into a thick sticky gel when it cools! I went back to the soap calc and realized then that I had made a big mistake! I used 10 ounces less water than I should have. I have tested my paste with Phenolphthalein solution and it is absolutely clear as it was before I began diluting. I know you said not to trust the ph strips but they are all I have but my strips show it to be very mild between a 6 and 7. But as I said no matter how much water I add when it cools it's becomes a very thick amber gel again. My husband loves it and it gets a fantastic creamy bubble but I don't know if it is safe to use or if I should just throw it out? My husband doesn't want me to throw it away but I don't want him using something that could be unsafe. Could you please offer some advice because I just don't know what to do with it and I would sure appreciate any light you can shed.

    ReplyDelete
    Replies
    1. Hi Traci - if your phenolphthalein tests clear, your paste is good to go and should not have any excess lye. Dilution rates will vary depending on many things including your formula. Those high in olive oil will require more water to fully dilute than those high in coconut oil. Strips indicating a pH of 6 or 7 is why I do not use them - true soap made from KOH is an alkaline product (liquid soap will have a natural pH range of 9.0 - 10.2 or so without the addition of any additives) and if that pH goes below 8.5 or so (typically this happens by adding too much of a pH adjuster like citric acid), it loses that alkalinity and will start to separate and break down into some soap, water, fatty acids and potassium citrate (if citric acid was used) - the saponification starts reversing.

      It sounds like you just need more dilution water. I am curious as to what your paste weight was before you started to dilute and how much dilution water you have added so far and if you have added anything else besides the dilution water.

      Delete
  3. Hi! Thanks for your great post! My soap keeps separating after 24 hours and it is not a ph problem. Is there any other reason for this? Water quantity? Longer time in crockpot? Thanks for any help! Paola (Spain)

    ReplyDelete
    Replies
    1. HI Paola - without knowing more details about your formula, process and any additives you may have used, it is hard to help diagnose what might be going on. Did you use too high a superfat and the excess fats are floating on top, too many oils high in unsaponifiables - there are many, many reasons you could be having problems.

      Delete
  4. HI Faith! Thanks for your quick answer and sorry for the lack of info, I'm new at this! I used the following recipe:
    Castor Oil 9.33% (1oz)
    Coconut Oil 9.33% (1oz)
    OIive Oil 81.33% (6oz)
    4 oz of glycerin + 2 oz of KOH
    I heated up the glycerin before adding the KOH (but didn't get any bubbling???), added them to the oils, got to trace very quickly and cooked for 3 1/2 hours when I got the clarity test ok. I added 40oz of distilled water (3:1 ratio) and went on cooking on the low setting for another 3 1/2 hours, cooled it off and bottled it. The next morning it had separated into a darker, clear soap (I tried it, it works!) at the bottom and a clearer, opaque version at the top. I took it back to the crockpot, added water to take it to a 4:1 ratio and cooked for another 2 hours. Same thing!!! What am I doing wrong? And can I save this batch somehow? I was thinking of adding xantham gum to stabilize the whole lot.
    Thanks!!! Paola

    ReplyDelete
    Replies
    1. Hi Paola,

      Something is not right with your formula and your percentages:
      You should have:

      Castor Oil 12.5% (1oz)
      Coconut Oil 12.5% (1oz)
      Olive Oil 75% (6oz)

      with a total of 8 ounces oils being used. You do not calculate the glycerin as part of your oils (not sure if that was what you were doing). With the above oils and a 0% superfat you would need:

      1.68 ounces Potassium Hydroxide (KOH)
      5 ounces liquid

      Based on the numbers you have, it looks like you have quite the lye excess. Are you missing an oil? Did you neutralize your soap after dilution to account for the lye excess?

      Delete
  5. No, not missing anything, the % may be off since I'm translating from grams to ounces, but the weight itself is ok. Would an excess of lye cause separation?I'm still waiting for the ph reactant to arrive. How would you go about neutralizing this? With citric acid?

    ReplyDelete
    Replies
    1. No - an excess lye would not cause separation but your soap will be highly caustic and not safe to use. If you did not add anything other than distilled water you should not have separation. Why did you cook an additional 3 1/2 hours after dilution or do you mean it took 3 1/2 hours to fully dilute your soap?

      One thing to keep in mind, if you create your paste using the glycerin method and you stick blend for too long, you will get a dark fluid, liquidly layer on the bottom and a thick, fluffy lighter layer on the top - BUT this will all incorporate once you dilute - it is just a sign you stick blended for fat too long.

      Without you knowing if you have excess lye via phenolphthalein drop testing (or a zap test of the paste) and what your soap pH is, it is hard to diagnose what could have happened to it.

      Delete
  6. Hi again! Thanks so much for your time! I have tried ph strips now that the soap is cold and they read 8.5. I know this is not the best method so I'm going to wait for the ph reactant to get here. I put it back in the crockpot because I thought (the first time it separated) that I hadn't given it enough time to dillute properly. I also added a bit of water that second time. I have the feeling this white stuff is what didn't get to saponify but, for the time being, I'm going to let it be until I get the phenolphthalein and I'll take it from there. Thanks again for your time! I'll keep you posted! :-)

    ReplyDelete
  7. I really need help. So I'm also using the Castile Liquid Soap Paste from Bramble Berry and I had gotten them to send me directions and dilution ratios which I followed. But after about an hour and half of cooking on the stove, all of the liquid disappeared and it all turned back into one big pasty glob. Unsure of what to do (and with the Bramble Berry support team MIA) I added more water in. It's returned back to how it was before, but now I have no idea at all if I'm on the right track or wasting my time. Any help you could provide would be amazing! Right now I'm just kind of sadly stirring what I have on the stove in hopes that it'll magically turn into something usable later.

    ReplyDelete
    Replies
    1. HI Christine - 100% olive oils soap needs quite a bit of water to fully dilute - anywhere from 3 to 6 times the weight of the paste. If you are using heat to dilute your paste, the water is probably evaporating which is why your paste is not fully diluting or diluting then solidifying again as it cools. What you should do is add boiled distilled water to your paste, cover the container in which you are diluting and give it time without added heat or very, very low heat. The more heat you apply, the fast it will dilute, but the more of your dilution water you will lose to evaporation.

      Once you get it fully diluted, weigh your diluted soap and subtract the amount of your initial paste weight. This number is the amount of water you needed to add to fully dilute your paste. Be patient or you run the risk of over diluting your soap.

      Delete
  8. Hi Faith. I have few questions need your help.

    What thickener you used to thicken liquid soap?

    I have made 100% coconut oil liquid soap and try to thicken it but fail to do it. Any advice on this?

    Thank you.

    ReplyDelete
    Replies
    1. Hi there - my thickener of choice is HEC - Hydroxyethyl Cellulose. It is consistent for all formulations and does not create any cloudiness within the soap. Please look under Liquid Soap Tutorials for more information on using this thickener.

      Delete
  9. Hi Faith, I have a question to ask about separation. i bought liquid castile soap and tried to add eo. and separation happened. what should i do to fix that? is there any ingredients that can bind them together?

    ReplyDelete
    Replies
    1. It is not uncommon for fragrance oils or essential oils to strange things to liquid soap. It is always recommended that you test a new fragrance or essential oils on a small portion of soap prior to adding it to a larger batch. I prefer to add my fragrance and essential oils to warm soap (about 120 F) to help them incorporate better. If you added it cold, maybe heat it up to about 120 (put the soap in a clean mason jar, cover it and set it in a pot of warm to hot water to heat it up) and see if that helps.

      Some people like to add solubizers (polysorbate 20 or 80) or fragrance modifiers to help distribute the oils in the soap, but I find those to be a bit sticky and end up with cloudy soap or additional problems so I avoid using them and stick with FO's and EO's that have passed my testing.

      Delete
  10. Hello,
    This is my first batch of trying my hand at liquid soap. I used:
    32 oz of canola oil
    16 oz of coconut oil
    8 oz of sunflower oil
    potassium hydroxide

    My soap never went to the taffy stage but after cooking in a cockpot for 6 hours. It did get to the mashed popatoe stage. I tested and it came out clear. Turn it off and let it set overnight. Heated up 2 1/2 gallons of distilled water with borax.
    After 3 days sitting, I see crystals on the top of my soap. I saw that you just filter the soap through some cheese cloth. Also, I didn't know about testing your pH levels in the soap.
    I don't know if my soap is good to use or not. Please advice for me.
    Thank you for your web page! It is more helpful then just a recipe to use.
    Theresa

    ReplyDelete
    Replies
    1. Hi Theresa - I will help as best I can. First off, for you first batch of liquid soap, that is quite a large amount of oils. I would start off with 16 - 20 ounces of oils. This will allow the process to go a bit quicker so that you can see the stages your formulation will go through. You did not mention how much KOH or water you used so I have no idea if you formulated with a lye excess or not. You mentioned you used borax with your dilution water - what was your reason for this? Borax is used to neutralize excess lye and can thicken some formulations. No lye excess, no need for borax. The crystals you are seeing may be from too much borax.

      Here are some tips:
      - Reformulate to use 16 - 20 ounces oils to start with.
      - Run the formula through the summerbee meadow or brambleberry calculator with a 0 - 1% superfat amount. This should allow all your oils to saponify without a lye excess that you will need to neutralize later with borax or citric acid.
      - Get phenolphthalein drops to test for excess lye when making your paste - that combined with your clarity test is very helpful in determining if your paste has thoroughly cooked.
      - Once you have determined your paste is complete, you can dilute with just distilled water as you have no lye excess to neutralize.

      Delete
  11. Help....I've tried a reicpe.for liquid soap twice now ( I will post the recipe below). I'm getting it to the mashed potato stage but it would gel. I'm frustrated....any suggestions??

    Recipe is:
    24 oz olive oil
    1.71 oz castor oil
    4.29 oz coconut oil
    6.28 oz KOH
    18.86 oz distilled water

    Right from brambleberry soap calc.

    I don't want to make this again and have to throw it away again. What am I doing wrong??

    Frustrated in Boston

    ReplyDelete
    Replies
    1. Not all soap pastes will look the same or like you might expect them to.
      A few questions:
      - Are you using heat and have you "cooked" your paste for any length of time?
      - Have you done a clarity test yet to determine if you have completely saponified all of your oils?

      Delete
  12. Hi Faith, I'm having problems with using fragrance oils. I use them at a 1-2% rate. In one case, they caused the soap to separate. In another, they caused the soap to become cloudy. Is there anything I can do to save the batch after the fragrance oils have caused these issues?

    ReplyDelete
    Replies
    1. Im having the same problem. Made ten bottles of liquid soap. There were all originally clear. Even after added essential oil, they were all clear. After few days, some turns cloudy and separation occurs and some still remains clear. I wonder what's wrong and how to save the batch. Would appreciate any advice.
      Thank you.

      Delete
  13. hi
    I just wanted to know if you had insight about cooking the diluted soap paste that uses lanolin. I diluted mine and I did test the oh it was a light pink
    then when I diluted it one 250 no batch was clear
    the second I used my store bought water and the end result was pink.
    is this because I cooked my larger batch longer and the lanolin?

    ReplyDelete
  14. Hi!
    How do I get rid of the settled insolubles? I hate the way it looks. I would love to have a perfectly clear/clean looking soap. Do you siphon or decant?

    This is my recipe...
    coconut 15.6oz
    olive 4.8oz
    soy 3.12oz
    almond .48 oz

    lye 5.93oz
    h2o 17.52oz

    ReplyDelete